Model APS-30
KEYLESS ENTRY ALARM UPGRADE MODULE
INSTALLATION INSTRUCTIONS
PRE-INSTALLATIONNOTES:
This system provides an output that should be used to drive the siren, but can be programmed to pulse the vehicle's horn.
When utilizing the horn, an additional relay is required. Caution: on many vehicles the factory horn is not designed
forcontinuoususe,anditisrecommendedthatthesirenisusedforthesevehicles.Checktoseeifthehorninthevehicle
is the same part that is used in a vehicle with the factory installed security system.
STAND ALONE PASSIVE ALARM
When installing the APS-30 as a stand alone passive alarm system, the dip switches must be set as follows;
Dip Switch # 1 = ON
Dip Switch # 2 = ON
Dip Switch # 3 = OFF
Dip Switch # 4 = OFF
Dip Switch # 5 = OFF
Dip Switch # 6 = OFF
DIP SWITCH SETTINGS
ON
OFF
PASSIVE ARMING
1 WIRE DISARM
HORN MODE
INSTANT TRIGGER
- ARM INPUT
1
2
3
4
5
6
ACTIVE ARMING
2 WIRE DISARM
SIREN MODE
ENTRY DELAY
+ ARM INPUT
HARDWIRE
VOLTAGE SENSE
PASSIVE / ACTIVE ARMING SELECTION : DIP SWITCH # 1
This alarm can be programmed to operate as either a " PASSIVE " or " ACTIVE " arming security system.
As a passive arming system, the alarm will automatically arm 30 seconds after the ignition key is turned off, one door is opened, then
all doors are closed. Additionally, if a door has been left opened, or if one of the trigger zones is defective, the system will always arm
10 minutes after the ignition key has been turned off, and ignore the defective trigger zone.
As an active arming system, the alarm will arm only when the vehicle’s doors have been locked using the existing OEM Keyless Entry
Transmitter.
The system is shipped from the factory in the active arming mode, and to select the passive arming mode, move dip switch # 1 to the "
ON " position.
1 OR 2 WIRE DISARM INPUT SELECTION : DIP SWITCH # 2
This alarm can be programmed for either 1 wire or 2 wire disarm operation.
ManyOEMkeylessentrysystemsuseon-boarddoorunlockrelays,whichusuallyresultsintheabilitytodisarmtheaftermarketsecurity
upgrademodulebyunlockingthedoorsusingthedoorpanelunlockswitch.Wiringthesystemfor2wiredisarmwilleliminatethisproblem.
The system is shipped from the factory in the 2 wire disarm mode, and to select the 1 wire disarm mode, move dip switch # 2 to the "
ON " position.
HORN OR SIREN OUTPUT SELECTION : DIP SWITCH # 3
VALET AND EMERGENCY OVERRIDE SWITCHES
This system provides individual inputs for two switches, a valet switch and a manual override switch. Moving these two functions to
separate switches provides an even higher level of security.
UNDERSTANDING DISARM #1 AND #2:
BecauseofthecomplexitiesofthedifferentfactoryRemoteKeylessEntryUnitsonthemarkettoday,theAPS-30uses(2)disarminputs.
Inallinstallations,whetherinstallingwitha2stepunlockcircuit,singlestepunlockcircuit,orastandalonepassivealarm, bothofthese
wires must be connected.
The following logic chart will help to demonstrate how these disarm inputs work. As shown in the chart, the APS-30 will disarm only
when Disarm inputs #1 and #2 are at opposing polarities.
Inaddition,whenDipSwitch#2issettotheONposition(1WIREDISARM),thealarmwillnotdisarmwhileitistriggered. Invehicles
with the single step unlock circuits, it is always best to set Dip Switch #2 to the OFF position (2 wire disarm), and wire according to the
Audiovox Tech Tips #22 and #23.
DISARM #1
RED WIRE
RESULT
APS-30 DISARMS
DISARM #2
RED / BLACK
WIRE
SCENARIO A
SCENARIO B
SCENARIO C
SCENARIO D
POSITIVE
POSITIVE
NEGATIVE
NEGATIVE
NEGATIVE
POSITIVE
POSITIVE
NEGATIVE
NO CHANGE IN ALARM
STATUS
APS-30 DISARMS
NO CHANGE IN ALARM
A small red L.E.D. is included that will serve as a visual indicator of the alarm status. It should be installed into the dashboard, located
where it is easily seen from outside the vehicle, yet not distracting to the driver.
STATUS
Once a location has been selected, check behind the panel for wire routing access, and to confirm the drill will not damage any existing
components as it passes through the panel.
Drill a 1/4 " diameter hole, and pass the red and blue wires from the L.E.D. through the hole, from the front of the panel. Firmly press
the body of the L.E.D. into the hole until fully seated.
VALET SWITCH
Select a mounting location for the valet switch, that is easily accessible to the driver of the vehicle.
The switch does not have to be concealed since it will in no way disarm the system from the armed or triggered state. The valet switch
may be mounted below or on the dashboard by drilling a 9/32 " diameter hole in the selected location. Before drilling, be sure to check
theareabehindthepanelforadequateclearanceforthebodyoftheswitch, andtobesurethatthedrillwillnotdamageanycomponents
as it passes through the panel.
MANUAL OVERRIDE SWITCH
Selectamountinglocationforthemanualoverrideswitch,thatisconcealed,anddoesnotnecessarilyhavetobewithinreachofthedriver.
Asecurelocationisinthetrunkofthevehicle,sincepressingthisswitchwillactivateatimer,whichwillthengivethedriver12seconds
to turn the ignition key to the " ON " position.
The manual override switch may be mounted by drilling a 1/4 " diameter hole in the selected location. Before drilling, be sure to check
theareabehindthepanelforadequateclearanceforthebodyoftheswitch, andtobesurethatthedrillwillnotdamageanycomponents
as it passes through the panel.
SIREN
Select a mounting location in the engine compartment that is well protected from access below the vehicle. Avoid areas near high heat
components or moving parts within the engine compartment. To prevent water retention, the flared end of the siren must be pointed
downward when mounted.
Mount the siren to the selected location using the screws and bracket provided.
HOOD AND TRUNK PIN SWITCHES
Two pin switches are included for use in protecting the hood and trunk ( or hatchback ) of the vehicle.
Theswitchesmustalwaysbemountedtoagrounded,metalsurfaceofthevehicle.Itisimportanttoselectalocationwherewatercannot
floworcollect, andto avoidall drip gutterson hood and trunk fenderwalls. Choose locations that are protectedby rubbergasketswhen
the hood or trunk lid is closed.
Thepinswitchescanbemountedusingthebracketsandscrewsprovided, ordirectmountedbydrillinga1/4"diametermountinghole.
Keepinmindthatwhenproperlymounted,theplungerofthepinswitchshoulddepressatleast1/4"whenthehoodortrunklidisclosed.
WIRING THE SYSTEM :
13PINCONNECTOR
RED FUSED WIRE - ( VOLTAGE SENSING ) : + 12 VDC CONSTANT BATTERY SOURCE
This wire controls the sensitivity of the voltage sensing circuit, which detects the turning on of an interior light when a door is opened.
Itwillalsodetecttheswitchingonofparkingorheadlamps, andinmanycaseswilltriggerthealarmwhenathermostaticallycontrolled
electronic cooling fan switches on.
It is recommended that when installing this system into vehicles with electronic " after fans, " the procedure for RED FUSED WIRE
- ( HARDWIRE ) should be followed.
In voltage sensing applications, the closer to the battery that this wire is connected, the less sensitive the voltage sense circuitry will be.
Moving the connection point to the fuse panel will increase the sensitivity of the voltage sensing circuitry.
RED FUSED WIRE - ( HARDWIRE ) : + 12 VDC CONSTANT BATTERY SOURCE
When hardwiring the control module to switches at all points of entry, the voltage sense circuit must be disabled. Move dip switch # 6
to the " OFF " position. Connect the RED wire to a + 12 VDC constant battery source.
WHITE WIRE : + 12 VDC PULSED PARKING LIGHT OUTPUT ( 15 A MAX )
This wire is provided to flash the vehicle’s parking lights. Connect the WHITE wire to the positive side of one of the vehicle’s parking
lights.
WHITE w/ BLACK TRACE WIRE : POSITIVE OUTPUT TO SIREN OR HORN
This is a 3 A + 12 VDC transistorized switched or pulsed output when triggered ( see Dip Switch #3 ).
In the siren mode, connect this wire to the positive wire of the siren. Secure the black ground wire of the siren to chassis ground.
In the horn mode, connect this wire to terminal 85 of an external relay, connect terminal 86 of the relay to ground, and use the normally
open and common relay contacts ( 87 and 30 ) to pulse the vehicle’s horn, and move Dip Switch #3 to the "ON" position.
PURPLE WIRE : (+) DOOR TRIGGER
If the vehicle’s door courtesy light switches have a + 12 VDC output when the door is opened ( most Fords ), you must connect this
wiretothepositiveoutputfromoneofthedoorswitches.Donot connectthiswireattheilluminatedentryoutputfromthekeylessentry
module. You must connect this wire at the door ajar switch. In most cases, the PURPLE wire will only need to be connected to one
door switch, no matter how many doors the vehicle has.
IMPORTANT ! Do not use the PURPLE wire if the vehicle has ground output type door switches. (see BROWN wire).
YELLOW WIRE : + 12 VDC IGNITION SOURCE
Connect this wire to a source that is + 12 VDC when the key is in the on and crank positions, and off when the key is in the off position.
DARK GREEN w/ WHITE TRACE WIRE : ENTRY ILLUMINATION ( 300 mA MAX. )
The DARK GREEN w/ WHITE TRACE wire provides a 30 second ground signal whenever the system is disarmed using the OEM
transmitter, and pulses ground when the alarm is triggered.
It should be used to provide the optional entry lighting, and to flash the vehicle’s dome light when the alarm is sounding.
Thisisatransistorized,lowcurrentoutput,andshouldonlybeusedtodriveanexternalrelaycoil.ConnecttheDARKGREENw/WHITE
TRACE wire to terminal 86 of an external relay, connect terminal 85 of the relay to + 12 VDC battery, and wire the normally open and
common relay contacts ( 87 and 30 ) according to the polarity of the vehicle’s courtesy light circuit.
DARK BLUE WIRE : MANUAL OVERRIDE INPUT
Connect this wire to the DARK BLUE wire from the push-button manual override switch. Connect the BLACK wire from the switch
to chassis ground.
BLACK WIRE : CHASSIS GROUND
Connect this wire to a solid, metal part of the vehicle’s chassis.
ORANGE WIRE : 300 mA GROUND OUTPUT WHEN ARMED
Thiswireisprovidedtocontrolthestartercutrelay.ConnecttheORANGEwiretoterminal86oftherelay,andwiretheremainingrelay
contacts as shown in the wiring diagram.
WARNING ! Audiovox does not recommend using this relay to interrupt the ignition wire. Only connect this relay to the low
current solenoid feed wire, as indicated on the wiring diagram.
BROWN WIRE : (-) DOOR TRIGGER
Ifthevehicle’sdoorcourtesylightswitcheshavea-groundoutputwhenthedoorisopened(mostGMandImports)youmustconnect
thiswiretothenegativeoutputfromoneofthedoorswitches. Donot connectthiswireattheilluminatedentryoutputfromthekeyless
entry module. You must connect this wire at the door ajar switch. In most cases, the BROWN wire will only need to be connected
to one door switch, no matter how many doors the vehicle has.
IMPORTANT ! Do not use the BROWN wire if the vehicle has + 12 Volt output type door switches ( see PURPLE wire ).
LIGHT GREEN WIRE : (-) INSTANT TRIGGER ZONE 1
Thisisaninstantongroundtriggerwire. Thiswire(zone)shouldbereservedforconnectiontooptionalgroundoutputtriggerdevices
such as motion and/or shock impact sensors.
DARK GREEN WIRE : (-) INSTANT TRIGGER ZONE 2
This is an instant on ground trigger wire. It must be connected to the previously installed hood and trunk pin switches.
4PINCONNECTOR
IMPORTANT ! When installing the APS-30 as a stand alone passive security system, the RED wire in this connector must be
connected to a + 12 VDC switched ignition source. RED w/BLACK and GREEN wires must be connected to
ground. The BLUE wire in this connector will not be required for the stand alone installation.
WIRING THE ARM / DISARM INPUTS IN VEHICLES WITH REMOTE 2 STEP UNLOCK
The following represents the most common wiring routine in vehicles using the remote 2 step unlock feature.
Dip switches #2 & #5 must be switched to the OFF position in these cases.
GREEN WIRE : ARM INPUT
Connectthiswiretothedriver'sdoorlockmotorwire, whichwillreceive+12voltswhenthedoorsarelocked
using the door panel switch or the remote transmitter.
RED WIRE : DISARM INPUT #1
Connectthiswiretothedriver'sdoorunlockmotorwire,whichwillreceive+12voltswhenalldoorsareunlocked
using the door panel switch or the remote transmitter.
RED w/BLACK TRACE WIRE : DISARM INPUT #2
Connect this wire to any passenger door unlock motor wire, which will receive +12 volts when all doors are
unlocked using the door panel switch or the remote transmitter, but will not receive the +12 volt pulse when
only the driver's door is unlocked using the remote transmitter.
TYPICAL ONE-STEP DIAGRAM
TYPICAL 2-STEP DIAGRAM
FACTORY
REMOTEKEYLESS
ENTRY MODULE
CONNECT
"DISARM INPUT #2"
TO CHASSIS GROUND
DRIVER'S
DOOR UNLOCK
RELAY
DRIVER'S
CONNECT
DRIVER'S
D/L MOTOR
D/L MOTOR
"DISARM INPUT #1"
FACTORY
REMOTEKEYLESS
ENTRY MODULE
HERE.
+
ALL
UNLOCK
OUTPUT
ALL
LOCK
OUTPUT
RIGHT FRONT
D/L MOTOR
RIGHT FRONT
D/L MOTOR
ALL
ALL
CONNECT
"DISARM INPUT #2"
HERE.
UNLOCK LOCK
OUTPUT OUTPUT
CONNECT "DISARM
INPUT #1" HERE
RIGHT REAR
D/L MOTOR
RIGHT REAR
D/L MOTOR
THEN CUT THE WIRE
AND ADD
A
DIODE,
AS SHOWN.
IF GROUND SWITCHED
DOOR LOCKS TURN
DIODE TO FACE INTO THE
KEYLESS MODULE AND
CONNECT DISARM #2 TO
+12 VOLTS
LEFT REAR
D/L MOTOR
LEFT REAR
D/L MOTOR
-
FACTORY
DOOR LOCK
RELAYS
FACTORY
DOOR LOCK RELAYS
CONNECT
"ARM" INPUT
HERE
CONNECT
"ARM" INPUT
HERE
DOOR PANEL
LOCK / UNLOCK
SWITCH
DOOR PANEL
LOCK / UNLOCK
SWITCH
+
+
+
+
UNLOCK
UNLOCK
UNLOCK
LOCK
UNLOCK
LOCK
LOCK
LOCK
WIRING THE ARM / DISARM INPUTS IN VEHICLES WITHOUT 2 STEP UNLOCK
GREEN WIRE : ( + or - ) ARM INPUT
Connectthiswiretothedriver'sdoorlockmotorwire,whichwillreceive+12voltswhenthedoorsarelocked
using the door panel switch or the remote transmitter.
RED WIRE : DISARM INPUT # 1
Connect this wire to the unlock output wire from the OEM keyless entry control module. Refer to the
diagram..
RED w/ BLACK TRACE WIRE : DISARM INPUT # 2
If the Red wire is switched to +12 volts when the doors are unlocked, connect the Red w/Black Trace wire
to ground.
If the Red wire is switched to ground when the doors are unlocked, connect the Red w/Black Trace wire
to +12 volts.
BLUE WIRE : (+) TRUNK TRIGGER SHUNT INPUT
This wire will determine if the vehicle’s trunk has been opened using the OEM transmitter, and stop the alarm from triggering when
the transmitter is used.
Connect this wire to the + 12 volt trunk release output from the OEM Keyless Entry module.
VALET SWITCH : Plug the 2 pin connector from the valet switch into the mating 2 pin connector on the control module.
L.E.D. : Plug the 2 pin connector from the L.E.D. into the mating 2 pin connector on the control module.
Printed in Taiwan
128-4515
Audiovox Corp., 150 Marcus Blvd. Hauppauge, N.Y. 11788
Form No.
|