Q Logic Computer Hardware Q L E 4 0 6 0 C User Guide

[ Quick Start Guide ]  
i S C S I H B A I N S T A L L A T I O N  
d
®
QL A 4 0 5 0 / 4 0 5 0 C / 4 0 5 2 C  
Q L E 4 0 6 0 C / 4 0 6 2 C  
 
Quick Start Guide  
Installation Instructions  
®
This Quick Start Guide describes how to install and configure your new QLogic SANblade host bus adapter (HBA) and  
SANsurfer iSCSI HBA Manager application in four simple steps:  
Step 1. Verify the package contents.  
Step 2. Install the HBA hardware.  
Step 3. Install the HBA driver.  
Step 4. Install the SANsurfer iSCSI HBA Manager application.  
Keep the HBA in the antistatic bag until installation. The HBA contains parts that can be damaged by  
electrostatic discharge (ESD). Before handling the HBA, use standard methods to discharge static  
electricity. Place the HBA on the bag when examining it. Retain the bag for future use.  
CAUTION!  
System Requirements  
Your system must have the functionality described in the following sections to support the QLogic SANblade HBA.  
Minimum Software Requirements  
®
Windows 2000: Service Pack (SP) 4 or later (QLA405x HBAs)  
®
Windows Server 2003 SP 1 or SP 2  
Windows XP Pro SP 1 or SP 2  
Windows PE 2.0, 2004, 2005  
Windows Vista (Business and Enterprise)  
®
Linux Red Hat Enterprise Linux 3.0 Update 7 or later (QLA405x HBAs), Linux Red Hat Enterprise Linux 4.0  
Update 3 or later (QLA405x and QLE406xC HBAs)  
Novell SUSE Linux: SLES 8 Update 3 or later (QLA405x HBAs), SLES 9 Update 2 or later (QLA405x and  
QLE406xC HBAs), SLES 10 (QLA405x and QLE406xC HBAs)  
Solaris: Solaris 9 or later for Solaris SPARC and x86 (IA32 and x64)  
®
VMware 3.0.1 (QLA405x HBAs)  
NOTE:  
The operating systems listed above are applicable to all HBA models unless otherwise noted.  
Minimum Hardware Requirements  
Empty PCI-X 32-bit or PCI-X 64-bit slot (QLA405x HBAs), 2.5-GHz PCI Express x4 slot (QLE406xC HBAs)  
PCI-X: 3.3-volt signaling (QLA4050 HBAs); 3.3V or 5-volt signaling (QLA4050/4052C HBAs)  
The correct media:  
QLA4050: 62.5/125-μM multimode fiber  
QLA4050C/4052C, QLE4060C/4062C: UTP copper (Cat5E or Cat6)  
The correct connectors:  
QLA4050: LC duplex  
QLA4050C/4052C, QLE4060C/4062C: RJ45  
1
 
Step 1. Verify the Package Contents  
The QLogic HBA is shipped with the following items:  
QLogic SANblade HBA  
Low-profile bracket (not available in all models)  
Quick Start Guide (this document)  
®
SANsurfer for SANblade iSCSI HBAs CD(s)  
Step 2. Install the HBA Hardware  
NOTE:  
When installing the QLogic HBA and driver in a Solaris system that does not already have QLogic HBAs or  
drivers installed, please install the QLogic Solaris driver before you install the QLogic HBA hardware. This allows Solaris  
to correctly bind the QLogic Solaris driver to the QLogic HBA. Failure to do so will require an additional system reboot  
after the driver is loaded.  
To install the HBA hardware, you need to open the computer and locate the appropriate bus slot. If necessary, consult  
your computer system manual for instructions to remove the computer cover.  
Depending on the HBA you are installing, the bus connector will look like one of the following samples:  
PCI-X  
PCI Express  
QLA4050  
N/A  
Optical  
QLA4050C  
QLA4052C  
QLE4060C  
QLE4062C  
Copper  
Follow these steps to install the HBA hardware:  
1.  
2.  
Power off the computer, then disconnect the power cable.  
Remove the computer cover and find an empty bus slot.  
2
 
3.  
4.  
5.  
6.  
7.  
Pull out the slot cover (if any) by removing the screw or releasing the lever.  
Grasp the HBA by the top edge and seat it firmly into the slot.  
Refasten the HBA’s retaining bracket using the existing screw or lever.  
Close the computer cover.  
Plug in the power cable and turn on the computer.  
HBA  
LEVER  
64-BIT PCI-X SLOT  
(QLA405x HBAs) OR  
SCREW  
PCI EXPRESS x4, x8, x16  
SLOT (QLE406xC HBAs)  
BA RETAINING BRACKET  
SLOT COVERS  
SYSTEM  
CHASSIS  
Sample motherboard and slots  
Step 3. Install the HBA Driver  
After you have completed the hardware installation and turned on the computer, insert the applicable SANsurfer for  
SANblade iSCSI HBAs CD into the CD-ROM drive, based on your operating system. Follow the instructions below for  
your operating system.  
The latest drivers and documentation can be found on the QLogic Web site, www.qlogic.com.  
Windows 2000 (QLA405x HBAs only)  
NOTE:  
If an earlier version of the Windows 2000 driver is already installed, see the readme file for information about  
updating the existing driver.  
Perform the following steps to install the HBA driver for Windows 2000:  
1.  
2.  
Log onto the computer as Administrator.  
Download and save the HBA driver to your hard drive:  
a.  
TypeorbrowsethepathtotheQLogic driverdirectoryontheapplicable SANsurferforSANblade  
iSCSI HBAs CD. For example:  
<CD-ROM Drive Letter>:\autoplay\iSCSI_HBA_drivers\Windows  
b.  
c.  
Locate and launch (double-click) the executable (.exe) file containing the driver.  
Whenprompted, typeorbrowsetoalocationonyourharddrivetostorethedriverfiles. ClickOK.  
3.  
Windows detects the newly installed device, then displays the Found New Hardware with Ethernet  
Controller message. Click Next.  
3
 
 
4.  
In the Install Hardware Device Drivers dialog box, select Search for a suitable driver for my device  
(recommended). Click Next.  
5.  
6.  
In the Locate Driver Files dialog box, select Specify a Location. Click Next.  
In the Copy manufacture's files from: dialog box, type or browse the path to the directory where you  
stored the driver files (see step 2). Click OK.  
7.  
8.  
9.  
In the Driver Files Search Results dialog box, click Next.  
In the Completing the Found New Hardware Wizard dialog box, click Finish.  
The Found New Hardware - Network Controller message displays. The Found New Hardware Wizard  
program is launched to begin installing the driver for the QLogic iSCSI HBA. Click Next.  
10. In the Install Hardware Device Drives dialog box, select Search for a suitable driver for my device  
(recommended). Click Next.  
11. Select specify a location. Click Next.  
12. In the Copy manufacture's files from: field, type or browse the path to the to the directory where you  
stored the driver files (see step 2).  
13. In the Driver Files Search Results dialog box, click Next.  
14. When the Digital Signature Not Found dialog box displays, click Yes.  
15. In the Completing the Found New Hardware Wizard dialog box, click Finish.  
16. If following message displays, click Yes:  
Your hardware settings have changed. You must restart your computer  
for these changes to take effect. Do you want to restart your  
computer now?  
NOTE:  
If you are installing a dual-port QLA4052C HBA, steps 316 must be repeated for the second port.  
Windows Server 2003  
NOTE:  
If an earlier version of the Windows Server 2003 driver is already installed, see the readme file for information  
about updating the existing driver.  
Perform the following steps to install the HBA driver for Windows Server 2003:  
1.  
2.  
Log onto the computer as Administrator.  
Download and save the HBA driver to your hard drive:  
a.  
TypeorbrowsethepathtotheQLogic driverdirectoryontheapplicableSANsurferforSANblade  
iSCSI HBAs CD. For example:  
<CD-ROM Drive Letter>:\autoplay\iSCSI_HBA_drivers\Windows  
b.  
c.  
Locate and launch (double-click) the executable (.exe) file containing the driver.  
Whenprompted, typeorbrowsetoalocationonyourharddrivetostorethedriverfiles. ClickOK.  
3.  
Windows detects the newly installed device, then displays the Found New Hardware with Ethernet  
Controller message.  
4.  
5.  
Select Install from a list or specific location (Advanced), then click Next.  
SelecttheSearchforthebestdriverintheselocations option. Typeorbrowsethepathtothedirectory  
where you stored the driver files (see step 2), then click Next.  
6.  
7.  
8.  
In the Security Alert - Driver Installation dialog box, click Yes.  
In the Completing the Found New Hardware Wizard dialog box, click Finish.  
The Found New Hardware Wizard with Network Controller message displays. The Found New  
Hardware Wizard program is launched to begin installing the iSCSI driver for the QLogic iSCSI HBA.  
9.  
Select Install from a list or specific location (Advanced). Click Next.  
10. SelecttheSearchforthebestdriverintheselocations option. Typeorbrowsethepathtothedirectory  
where you stored the driver files (see step 2).  
4
 
   
11. In the Hardware Installation - Windows Logo dialog box, click Continue Anyway.  
12. In the Completing the Found New Hardware Wizard dialog box, click Finish.  
Windows Vista  
Initial Operating System Installation with the HBA Driver as Boot or as an Add-On  
Perform thefollowingstepsto installtheWindows Vistaoperating system andtheHBAdriver(as boot as orasan add-on):  
1.  
2.  
Start the Windows installation procedure using the Setup CD.  
The following message displays:  
Which type of installation do you want?  
Select Custom (Advanced).  
3.  
4.  
The following message displays:  
Where do you want to install Windows?  
Select Load Driver.  
Download and save the HBA driver to your hard drive:  
a.  
TypeorbrowsethepathtotheQLogic driverdirectoryontheapplicable SANsurferforSANblade  
iSCSI HBAs CD. For example:  
<CD-ROM Drive Letter>:\autoplay\iSCSI_HBA_drivers\Windows  
b.  
c.  
Locate and launch (double-click) the executable (.exe) file containing the driver.  
Whenprompted, typeorbrowsetoalocationonyourharddrivetostorethedriverfiles. ClickOK.  
5.  
6.  
At the Load Driver screen, type or browse the path to the directory where you stored the driver files  
(see step 4), then click OK.  
Click Next to continue with the standard installation procedure.  
Adding the HBA Driver to an Existing Operating System  
Perform the following steps to add the HBA driver to an existing operating system:  
1.  
After installing the iSCSI HBA and restarting your computer, download and save the HBA driver to  
your hard drive:  
a.  
TypeorbrowsethepathtotheQLogic driverdirectoryontheapplicable SANsurferforSANblade  
iSCSI HBAs CD. For example:  
<CD-ROM Drive Letter>:\autoplay\iSCSI_HBA_drivers\Windows  
Locate and launch (double-click) the executable (.exe) file containing the driver.  
Whenprompted, typeorbrowsetoalocationonyourharddrivetostorethedriverfiles. ClickOK.  
b.  
c.  
2.  
Windows detects the newly installed device and displays the Found New Hardware message.  
The Hardware Update Wizard program starts installing a device driver for the newly installed device.  
Select the Driver tab, then click Update Driver to start the Hardware Update Wizard.  
Select Browse my computer for driver software, then click Next.  
3.  
4.  
5.  
6.  
7.  
Select Let me pick from a list of device drivers on my computer, then click Next.  
Click Have Disk.  
On the Install from Disk screen, select the directory where you stored the driver files (see step 1),  
then click OK.  
8.  
9.  
When the Update Driver Software Wizard/Select QLogic iSCSI Adapter window displays, click Next.  
Click Close on the Update Driver Software Wizard window.  
5
 
   
Linux (Driver and RAMDisk Image)  
The following installation instructions are applicable to SLES 9 (or later) or Red Hat Enterprise Linux 4.0 (or later). For  
more information and driver installation instructions for other Linux operating system versions, see the README.txt file  
associated with the driver.  
1.  
2.  
3.  
Download the latest driver file qla4xxx-vx.yy.zz.tar.gz from the SANsurfer for SANblade iSCSI HBAs  
CD. The driver is located in the following directory: autoplay\iscsi_HBA_drivers\Linux  
Type the following to uncompress the tar file:  
# tar -xvzf *.gz  
Type the following to compile the driver:  
# cd x.yy.zz  
# ./extras/build.sh install  
4.  
5.  
Type the following to load the driver:  
# modprobe –v qla4xxx  
Optionally, type the following to compile the driver and create a RAMDisk image that will automatically  
load the driver when the system is rebooted:  
# ./extras/build.sh initrd  
To unload the driver, type the following:  
# modprobe –r qla4xxx  
Solaris  
NOTE:  
If an earlier version of the Solaris driver is already installed, you must un-install this driver before installing  
the latest driver. For more information, see the section in the README.txt file about removing the driver.  
1.  
2.  
Login to the Solaris system as root.  
Type the following command to uncompress the package:  
uncompress <directory containing package file>/qla4xxx.Z  
Type the following command to start the package installation:  
pkgadd -d <directory containing package file>/qla4xxx  
Follow and answer the prompts displayed to finish the installation.  
3.  
4.  
a.  
b.  
c.  
When the package selection prompt displays, enter the number corresponding to the driver  
package applicable to the Solaris version installed on the target system.  
At the driver destination prompt, press ENTER to place the driver in the default directory, which  
is usually /kernel/drv.  
When prompted to continue and to complete the QLogic driver installation procedure,  
press Y.  
For more help, see the Solaris man page on pkgadd.  
After the pkgadd program completes, type the following command to reboot the system:  
reboot -- -r  
5.  
NOTE:  
Modify the system sd.conf file (/kernel/drv/sd.conf) for the operating system to recognize new targets. QLogic  
recommends adding up to 255 targets. The QLogic SANblade HBA supports up to 128 devices.  
6
 
To unload the driver, perform the following steps:  
1.  
2.  
Login to the Solaris system as root.  
Type the following command:  
pkgrm QLA4xxx-0  
3.  
Type the following command to reboot the system:  
reboot -- -r  
Step 4. Install the SANsurfer iSCSI HBA Manager Application  
To install the SANsurfer iSCSI HBA Manager application:  
1.  
Insert the applicable SANsurfer for SANblade iSCSI HBAs CD into your CD-ROM drive (if the auto-run  
screen does not appear, open the start_here html page with your browser.)  
2.  
3.  
4.  
5.  
6.  
Select your operating system.  
Click I Accept on the License Agreement.  
Click to select the specific version of your operating system.  
Select the SANsurfer iSCSI HBA Manager install file.  
Follow the on-screen directions and installation prompts.  
Congratulations! You have successfully installed your QLogic HBA and  
management application!  
To obtain the most current drivers, management applications, user instructions, and documentation, please  
visit the QLogic website at www.qlogic.com/support and download the latest versions.  
The following section contains additional information about the SANblade QLogic HBA, including the LED  
scheme, troubleshooting, warranty, technical support and certification information.  
HBA LEDs  
Table 1 lists the LED configuration for the QLogic QLA4050 HBA.  
Table 1. QLogic QLA4050 HBA LED Scheme  
Green LED  
Activity  
Link established  
Table 2 lists the LED configuration for the QLogic QLA4050C/4052C and QLE4060C/4062C HBAs.  
Table 2. QLogic QLA4050C/4052C and QLE4060C/4062C HBA LED Scheme  
Green LED  
Activity  
Link established  
Receive/transmit activity  
Flashing  
Troubleshooting and Technical Support  
The QLogic knowledge database contains troubleshooting information and documentation for the QLogic SANblade  
HBAs. The knowledge base is available to all users at http://support.qlogic.com.  
For technical support, visit our web site support.qlogic.com, email us at [email protected], or call at 952-932-4040.  
7
 
   
Warranty  
The QLogic SANblade HBA comes with a standard three year QLogic warranty. Please check the QLogic Web site at  
Laser Safety  
FDA Notice  
This product complies with DHHS Rules 21CFR Chapter I, Subchapter J. This product has been designed and manufactured according to  
IEC60825-1 on the safety label of laser product.  
Class 1 Laser Product  
Caution—Class 1 laser radiation when open  
Do not view directly with optical instruments  
Appareil laser de classe 1  
Produkt der Laser Klasse 1  
Luokan 1 Laserlaite  
Attention—Radiation laser de classe 1  
Ne pas regarder directement avec des instruments optiques  
CLASS I LASER PRODUCT  
Vorsicht—Laserstrahlung der Klasse 1 bei geöffneter  
Abdeckung  
Direktes Ansehen mit optischen Instrumenten vermeiden  
Agency Certification  
QLogic SANblade HBAs  
The following sections contain a summary of EMC/EMI test specifications performed on the following QLogic SANblade HBAs to comply  
with radiated emission, radiated immunity, and product safety standards:  
QLA4050  
(IS0710404)  
(IS0710407)  
(IS0710403)  
QLA4050C  
QLA4052C  
QLE4060C/QLE4062C (IX4010402)  
EMI and EMC Requirements  
FCC Part 15 compliance: Class B  
FCC compliance information statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including  
interference that may cause undesired operation.  
ICES-003 compliance: Class B  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du Canada.  
CE Mark 89/336/EEC EMC Directive compliance:  
EN55022:1998/CISPR22:1997—Class B  
EN55024:1998  
Immunity Standards  
IEC61000-4-2  
IEC61000-4-3  
IEC61000-4-4  
IEC61000-4-5  
IEC61000-4-6  
IEC61000-4-8  
IEC61000-4-11  
IEC61000-3-2  
IEC61000-3-3  
:
:
:
:
:
:
:
:
:
ESD  
RF Electro Magnetic Field  
Fast Transient/Burst  
Fast Surge Common/ Differential  
RF Conducted Susceptibility  
Power Frequency Magnetic Filed  
Voltage Dips and Interrupt  
Harmonic Current Emission  
Voltage Fluctuation and Flicker  
8
 
VCCI compliance: Class B  
AS/NZS CISPR22 compliance: Class B  
CNS 13438 compliance: Class B  
MIC compliance: Class B  
Korea MIC Class B Certified  
Product Name/Model  
Certification holder  
iSCSI HBA  
QLogic Corporation  
Manufactured date  
Refer to date code listed on product  
QLogic Corporation/USA  
Manufacturer/Country of origin  
B class equipment  
(Household purpose info/telecommunications  
equipment)  
As this equipment has undergone EMC registration for  
household purpose, this product can be used in any area  
including residential area.  
Korean Language Format— Class B  
Product Safety Compliance  
UL, cUL product safety compliance:  
UL60950  
CSA C22.2 No.60950  
Class 1 Laser Product per DHHS 21CFR (J)  
73/23/ECC low voltage directive:  
TUV:  
-EN60950-1:2001  
-EN60825-1  
-EN60825-2  
9
 
10  
 
© 2005–2007 QLogic Corporation. QLogic, the QLogic logo, the Powered by QLogic logo, SANbox, SANsurfer, and  
SANsurfer Management Suite are registered trademarks or trademarks of QLogic Corporation. All other brands and  
product names are trademarks or registered trademarks of their respective owners. Information supplied by QLogic is  
believed to be accurate and reliable. QLogic Corporation assumes no responsibility for any errors in this brochure.  
QLogic Corporation reserves the right, without notice, to makes changes in product design or specifications.  
 
*IS0054501-00C*  
QLogic Corporation  
949.389.6000  
26650 Aliso Viejo Parkway  
Aliso Viejo, CA 92656  
IS0054501-00 C  
J
 

Quantum Cell Phone ST00531 User Guide
Rancilio Coffeemaker RockySS User Guide
Renesas Stereo System M32R FPU User Guide
Rio Audio CD Player Advanced Digital Audio Center User Guide
Salton Coffee Grinder FAC500G User Guide
Samsung Digital Camera A502 User Guide
Samsung Microwave Oven ME18H704SFG User Guide
Sanyo Projector PLC ZM5000L User Guide
SATO Printer 8400RVe User Guide
Seiko Watch 5R65 User Guide