E X E C U T I V E
P R O G L I D E
S T E A M
I R O N
complies with
INTERNATIONAL
Model:
2 3 6 0 0
IEC60355
2200W
SAFETY SPECIFICATIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USE
2 y e a r g u a r a n t e e
MW_WX23600_PROGLIDE_IRON_IM.indd 1
7/21/2009 4:41:30 PM
IMPORTANT SAFEGUARDS
BEFORE FIRST USE
When using your iron, basic safety precautions
should always be followed:
•
•
It is normal for a small amount of smoke to be
produced the first time, this will quickly disap-
pear.
When using the steam function for the first
time, do not direct the steam towards the laun-
dry, as there could be debris from the steam
•
Make sure the voltage used corresponds with
the one indicated on the rating label.
Use the iron only for needed use as described
in the instruction manual.
•
Close supervision is necessary when any appli-
ance is used near children. Do not leave iron un-
attended while connected or on an ironing board.
Burns can occur from touching hot metal parts, hot
water or steam.
vents.
FILLING WITH WATER
•
Make sure that both the Steam Control turn-
ing Knob and Temperature Control Dial are in
“OFF” position.
•
•
Keep the iron out of reach of children.
The iron should never be left unattended while
it is connected to the mains supply.
Unplug the iron from the mains electrical sup-
ply before:
•
•
Hold the iron upright so that the water-filling
inlet is in a horizontal position.
•
Fill with water through Water Filling Inlet until
the water reach the “MAX” mark indicated on
the side of the iron, and never fill above this
mark.
1) Cleaning
2)Filling with water or emptying the water tank
3) Immediately after use
•
Never operate the iron with a damaged power
cord or plug, or after it has fallen or been dam-
aged in any way. To avoid the risk of electric
shock, do not disassemble the iron. Take it to
a qualified serviceman for examination and
repair.
SETTING TEMPERATURE
Follow the ironing instructions on the garment la-
bel. If there is no instruction but you do know the
kind of fabric, please consult the following table.
Note: If the fabric consists of various kinds of fab-
rics, always select the temperature required by the
most delicate fabrics.
•
•
Do not let the cord touch hot surfaces.
To protect against a risk of electric hazards,
do not immerse the iron in water or any other
liquid.
•
•
The iron must be used and rested on a stable
surface.
The iron is not to be used if it has been
dropped, if there are visible signs of damage
or if it is leaking.
FABRIC
Synthetic
Silk, wool
TEMP. CONTROL
TEMP. REQUIREMENT
Low temperature
•
••
Medium temperature
Cotton, linen
•••
High temperature
MW_WX23600_PROGLIDE_IRON_IM.indd 3
7/21/2009 4:41:32 PM
STEAM IRONING
DRY IRONING
•
•
Place the iron in a vertical position and set the
For ironing without steam, follow the instruction in
section “steam ironing”, however, the steam con-
trol turning knob should remain in position “O” (no
steam).
temperature control dial at the minimum/low
heat setting.
Insert the plug into the socket, and then turn
the temperature control dial to the “high heat”
marking. The pilot light will come on, indicat-
ing that the iron is heating up.
ANTI-CALC SYSTEM
•
•
When the pilot light turns off, the set tempera-
ture has been reached and the iron is ready
to use.
A special filter inside the water tank softens the wa-
ter and prevents scale build-up in the soleplate. The
filter is permanent and does not need replacing.
Note: Use tap water only. Distilled and demineral-
ized water makes the anti-calc system ineffective
by altering its physicochemical characteristics.
During ironing, the pilot light on the iron au-
tomatically switches on/off as the thermostat
maintains the set temperature (you may con-
tinue ironing during this process).
Turn the steam control turning knob to the re-
quired position.
•
•
SELF-CLEANING
Steam is produced as soon as the iron in held
horizontally.
The self-cleaning feature cleans inside the sole-
plate, removing impurities. We recommend using
it every 10-15 days.
SPRAYING
•
Set the steam control turning knob to Position
O (no steam).
•
Press the spray button to spray water on
clothes, as often as required.
•
•
Fill the water tank to maximum level.
Set the temperature control dial to MAX and
wait for the pilot light to turn off.
Note: When using the water spray function, en-
sure that there is enough water in the water tank,
and you may have to pump the spray button sev-
eral times the first time you use the iron in order
to start the spraying function.
•
•
Pull the plug out of the socket and press the
self-cleaning button until the boiling water,
steam, impurities come out.
When the soleplate has cooled down, you can
clean it with a damp cloth
BURST OR VERTICAL STEAM IRONING
HOW TO CLEAN AND STORE
•
Press the burst of Steam button to generate
a powerful burst of steam that can penetrate
the fabrics and smooth the most difficult and
tough creases. Wait for a few seconds before
pressing again.
•
After using, remove the plug from the socket,
lift the iron with the filling hole downwards
to empty the remaining water from the water
tank.
•
Insert the plug into the socket, and set the
Temperature Control Dial to “MAX” for 1-2
minutes to evaporate the remaining water,
and then unplug the iron and let it cool down
before storing it.
•
By pressing the Burst of Steam Button at in-
tervals you can also iron vertically (curtain,
hung garments, etc.)
Note: The burst steam function can only be used at
high temperature. Stop the emission when the pilot
light turns on, then start ironing again only after the
pilot light has turned off.
MW_WX23600_PROGLIDE_IRON_IM.indd 4
7/21/2009 4:41:32 PM
9.When placing the iron on its stand, ensure that
the surface on which the stand is placed is stable.
The iron is not be used if it has been dropped, if
there are visible signs of damage or if it is leaking.
ATTENTION:
The iron must not be left unattended while it is con-
nected to the supply mains. When the power cord
is damaged, contact your dealers or an authorized
service center for repair.
In case of any repairs, replacement of cord or plug,
or adjustment, please consult a qualified techni-
cian, or take appliance to an authorized service
facility.
NOTE:
1.This appliance is not intended for use by
persons(including children)with reduced physical,
sensory or mental capabilities, or lack of experi-
ence and knowledge, unless they have been given
supervision or instruction concerning use of the ap-
pliance by a person responsible for their safety.
2.Children should be supervised to ensure that
they do not play with the appliance.
3.The iron must not be left unattended while it is
connected to the supply mains;
4.The plug must be removed from the socket-outlet
before the water reservoir is filled with water (for
steam irons and irons incorporating means for
spraying water);
5.The filling aperture must not be opened during
use. Instructions for the safe refilling of the water
reservoir shall be given (for pressurized steam
irons);
6.The iron must only be used with the stand pro-
vided (for cordless irons);
7.The iron is not intended for regular use (for travel
iron);
8.The iron must be used and rested on a stable
surface;
MW_WX23600_PROGLIDE_IRON_IM.indd 5
7/21/2009 4:41:32 PM
TROUBLE SHOOTING
Problem
Reason
Action
Pre-caution
Iron is leaking water.
Temperature is too low
Set the temperature to steam setting (cotton)
Check fabric type is suitable for high steam
temperature
Steam switch is on self clean
function
Turn steam switch setting to steam or 0
position
Switch steam setting to 0 (off) after use or
when filling tank.
Tank is overfilled
Empty water tank
Fill to MAX mark only.
Iron is in the horizontal position
too long.
When adjusting item place iron down in the
vertical position
If iron is left on the item in the horizontal
position for too long it may burn the fabric.
Check temperature setting is suitable for
fabric type.
Iron is not heating up
Temperature control dial is in
the off position
Turn the temperature control dial to the
desired temperature setting.
Switch on household socket
Check the socket with another appliance
Household socket is off.
Household socket is not
working
Ensure iron is in the upright position.
Appliance must be of similar wattage to
prevent overloading.
Iron is tripping mains
Overloaded circuit.
Unplug all appliances attached to the same
circuit and check iron.
Note that there can be up to 5 household
plug sockets on 1 circuit.
Iron sticking to clothing
Temperature is too hot
Turn down temparature on control dial.
Clean and rinse item.
Check temperature setting is suitable for
fabric type.
Clothing is dirty or not rinsed
thoroughly.
Use spray function to dampen item and
check temperture is correct.
Use a old linen cloth to remove any trace
of dirt on the soleplate. Use iron soleplate
cleaner or methylated spirits for bad marks.
Check temperature setting is suitable for
fabric type.
Creases not coming out
Not Enough Steam
Item is too dry or temperature
too low.
Use steam function.
The steam control is off or set
too low.
Set the steam button/switch to on or full.
Ensure temperature control dial is set to the
3 dot position for steaming.
The iron temperature is
too low.
Set temperature control dial to MAX or 3 dot
position for steaming.
Check temperature setting is suitable for
fabric type.
The steam valve is blocked
due to water scale.
If your iron is fitted with a self clean function
carry out cleaning as per instructions.
Use distilled or demineralised water in your
iron to prevent blocking.
MW_WX23600_PROGLIDE_IRON_IM.indd 6
7/21/2009 4:41:32 PM
MW_WX23600_PROGLIDE_IRON_IM.indd 7
7/21/2009 4:41:32 PM
27 Nourse
Avenue Epping
2
Cape Town
P.O. Box 975 Eppindust 7475 South Africa
Tel: +27 21 534 8114 Fax: +27 21 534 8086
Service Centre Share Call: 086 111 5006
w e b : w w w. c r e a t i v e h o u s e w a r e s . c o . z a
MW_WX23600_PROGLIDE_IRON_IM.indd 8
7/21/2009 4:41:32 PM
|